Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Trusted Duct Repair & Sealing for Elmhurst Homeowners
The dust that keeps settling on your furniture and the room that never quite warms up often trace back to the same place: gaps and tears in your ductwork. Ducts in Elmhurst take a beating. Many of the homes here were built between the 1920s and the 1960s, when heating systems were retrofitted into tight basement and attic spaces, and the flexible and sheet-metal runs from that era have had decades to loosen at the joints, pull apart at the seams, and lose their insulation. When a return duct leaks in an attic, you’re pulling hot summer air and cold winter air straight into the system. When a supply joint separates, conditioned air dumps into a crawlspace instead of reaching your rooms.
Our technicians have up to 13 years of experience with this exact kind of work. We come out, find the leaks with a pressure test and a visual inspection, seal them properly, and then clean the system with professional-grade Rotobrush and Nikro equipment. A free estimate takes about an hour. Call (855) 410-4866.
What Our Duct Repair & Sealing Service Includes
Duct Sealing
Duct sealing is the process of closing the gaps where air escapes between duct sections, at seams, and where ducts meet registers or the air handler. You need it when your energy bills climb without explanation, when some rooms stay stubbornly cold, or when a pressure test shows significant leakage. We use mastic, mesh tape, and mechanical fasteners to close the leaks permanently, then re-test to confirm the system is holding pressure.

Flex Duct Repair
Flexible duct is the silver, accordion-style tubing you see running through attics and between joists. It’s convenient to install but it degrades: the inner liner cracks, the outer jacket tears, and the coil wire kinks. You’ll notice it when a room gets weak airflow or when you see condensation on the duct jacket. We cut out the damaged section, replace it with properly sized new flex, and re-hang it so it doesn’t sag or compress.

Metal Duct Repair
Sheet-metal ducts are strong but not indestructible. Joints separate at the seams, screws back out, and sections get crushed by remodel work or debris. You need metal duct repair when you hear rattling in the walls, when pressure drops across the system, or when a section is visibly dented. We repair the joint or replace the section, then seal it with mastic and mechanical fasteners that hold for the long haul.

Duct Insulation
Insulation wraps the duct to keep the air inside at the temperature the unit produced. In Elmhurst’s humid summers and cold winters, uninsulated runs in attics and crawlspaces sweat, drip, and lose a large share of their cooling. You need new insulation when the old wrap is torn, compressed, or missing. We inspect each run, replace damaged insulation, and make sure the vapor barrier is intact and the wrap is properly supported.
Mastic Sealant
Mastic is the brush-on or trowel-on sealant that professional HVAC technicians use on duct joints, plenum connections, and register boots. It’s not tape, and it’s not foam: it bonds to the metal or flex and stays flexible through years of temperature swings. You need it wherever the joints are loose, the old sealant has cracked, or you want a permanent seal instead of a temporary patch. We apply mastic to every joint we repair and inspect the rest of the system for similar issues.
Air Leak Repair
Air leaks are the hidden inefficiency that shows up as high bills and uneven comfort. They occur at register boots, at return plenum connections, at flex duct collars, and where ducts pass through walls or floors. You need air leak repair when a pressure test confirms more than a small amount of leakage or when you can feel air blowing at a joint. We test the system, find the leaks with a pressure gauge and smoke, and repair each one at the source.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Brands We Service for Duct Repair & Sealing
We work on duct systems connected to equipment from Honeywell and Aprilaire, and we see the same wear patterns across the popular makes. Honeywell zone dampers and control components often develop loose linkages that make one zone leak air while the other runs fine. Aprilaire humidifiers and air cleaners tie into the ductwork at the plenum, and those connections need to be properly sealed and insulated after any service. We know where these components fail and how to repair the ductwork around them.
The flex and metal ducting we repair comes from several manufacturers, and the failure points are fairly consistent: collars loosen at the boot, the inner liner cracks on flex, and the seams on sheet metal open up after years of temperature cycling. Our technicians have up to 13 years of hands-on experience with this kind of repair, and we use Rotobrush and Nikro equipment to clean the ductwork once the repairs are sealed and the system is holding pressure. Whether you have Honeywell, Aprilaire, or any other make of duct system, we can help.
Signs You Need Duct Repair & Sealing Right Now
- Dust keeps settling on the furniture. Leaky return ducts pull attic, crawlspace, and wall-cavity dust straight into the airstream and distribute it through the house. If you wipe a shelf and it’s dusty again within a day or two, the ducts are a likely source.
- Some rooms never get comfortable. A room that’s always cold in winter or hot in summer, while the rest of the house is fine, usually has a loose joint or a disconnected run feeding it. Sealing that one connection can restore the room without touching the thermostat.
- Your energy bills climbed without explanation. A leaking duct system forces the furnace or air handler to run longer to make up for the air that never reaches its destination. The bill increase is a symptom; the leak is the cause.
- You hear whistling, rattling, or a rush of air at the registers. A high-pitched whistle usually means air is escaping through a gap. Rattling can mean a disconnected or vibrating section. Either way, the noise points to a joint that needs attention.
- You see dust streaks or condensation near a register. Dark streaks on the ceiling around a register, or damp insulation on a flex duct in the attic, mean air is escaping at that point and the surrounding building material is affected. This one is worth checking sooner rather than later because moisture can lead to bigger problems.
Our Duct Repair & Sealing Process – Step by Step
- 1
We inspect the whole system. That means eyes on every accessible duct run, every register boot, the air handler, and the main trunk lines. We take note of the duct material, the age of the installation, and any areas where the insulation is failed. Our technician walks you through what we found before anything is touched.
- 2
We pressure-test the ducts. A pressure gauge and smoke test show us the leakage rate and help pinpoint where the leaks are concentrated. This is the difference between a quick visual pass and an actual diagnostic measurement, and it tells us what we need to repair.
- 3
We repair the damage. A damaged flex run gets cut out and replaced. A separated metal joint gets re-fastened and sealed with mastic. Every repair is made with the right material for the duct type, and every joint we touch gets sealed properly.
- 4
We re-test the system. After the repairs are done, we run the pressure test again to confirm the leakage is down and the system is holding. If anything’s still leaking, we find it and fix it before we call the job complete.
- 5
We clean and document. Once the system is sealed, we clean the ductwork with Rotobrush and Nikro equipment to clear the debris that’s accumulated, then take before-and-after photos of the ductwork so you can see exactly what was done.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Duct Repair & Sealing Cost in Elmhurst?
There isn’t a single price for duct repair. The range depends on the size of the system, the number of leaks, and the type of ducting involved. A typical small repair, like resealing one separated joint, is a straightforward job. A larger repair, like replacing a long flex run in an attic or sealing multiple joints across a whole-house trunk line, takes longer and involves more materials.
What affects the price: the number of leaks found during the pressure test, the accessibility of the ductwork (attic and crawlspace work is harder to reach than a basement run), the type of duct material (flex and metal need different techniques), and whether insulation needs to be replaced along with the repair. A whole-system sealing job is priced as one job, not by the vent or the leak, so you know the total before work starts.
The estimate is free, and the price is set per job by the written estimate. We don’t quote a number over the phone and then change it on site. What’s included in the estimate: the inspection, the pressure test, the repair, the re-test, and before-and-after photos of the ductwork. Call (855) 410-4866 for a free estimate – we’ll walk you through what we found before any work begins.
Duct Repair & Sealing Near Elmhurst – Our Service Area
We serve homeowners and property managers across the Elmhurst area, including Douglaston, Little Neck, Great Neck Plaza, Glen Oaks, Great Neck, Floral Park, Elmont, North New Hyde Park, Saddle Rock, Rego Park, and Corona. Whether you have a split-level in Douglaston, an apartment building in Corona, or a house in Glen Oaks, our team can assess the system and give you a clear written estimate. For nearby areas we also handle duct repair & sealing and duct repair & sealing throughout those neighborhoods.
Serving Elmhurst, NY – Our Local Coverage Area
We serve Elmhurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Duct Repair & Sealing in Elmhurst
Duct repair & sealing is the process of fixing damaged, disconnected, or leaking ductwork and then sealing the joints to keep conditioned air inside the system. It’s different from air duct cleaning, which removes dust and debris, and different from HVAC cleaning, which covers the equipment. A system with leaks can be clean and still waste a large share of the air it’s supposed to deliver. We handle it as part of our full Elmhurst Air Duct Cleaning service line, so the repair and the cleaning are done together and the system is tested before we leave.
Most duct repair jobs take between two and four hours, depending on the number of leaks and how accessible the ductwork is. A single joint reseal can be done in under an hour, while a whole-house sealing with multiple flex replacements takes longer. We give you a time window with the estimate so you know what to expect before we arrive.
Cost depends on the number of leaks, the type of ducting, and how much of the run needs work. We don’t give per-vent or per-leak pricing. Instead, the estimate covers the whole job, and you see the total before work starts. Call (855) 410-4866 for a free estimate – we’ll inspect the system and give you the written number.
Yes. We service duct systems connected to Honeywell and Aprilaire equipment, and we know where those connections tend to leak or loosen. If your system uses zone dampers or an inline humidifier tied into the ductwork, we account for those components during the repair and seal the connections properly. For systems with other makes of duct and equipment, we can help too.
We offer same-day service when the schedule allows, and dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed on Saturday. We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
The local pro we connect you with stands behind the repair work, with a satisfaction guarantee on the job. We take before-and-after photos of the ductwork so you can see what was repaired and sealed. If the system doesn’t hold pressure after our re-test, we find the problem and fix it before we leave. Call (855) 410-4866 for an exact quote – estimates are free.
The technician needs access to the furnace and air handler, the main duct trunk lines, and every room register. Clear a path to the mechanical closet and remove any items stored around the furnace or ducts. Point out any rooms that are hard to heat or cool, since that helps direct the inspection. If we’re also cleaning the system, expect a bit longer. For nearby areas we also handle duct repair & sealing throughout the Elmhurst area.
Schedule Your Duct Repair & Sealing Service in Elmhurst Today
Call (855) 410-4866 for a free estimate today. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Our team will inspect the system, run a pressure test, show you what we found, and give you a written per-job price before any work starts. One call covers assessment, repair, cleaning, and air quality treatment, with before-and-after photos so you know the job was done. If you’re scheduling duct work in a nearby neighborhood, we also handle duct repair & sealing and duct repair & sealing in those areas.
Written by the team at Elmhurst Air Duct Cleaning.